JBE-02V dome camera housing

JBE-502V

JBE-502V 5MP PoE Vandal-Resistant Dome Camera

The JBE-502V is a 5MP PoE dome camera with a vandal-resistant metal-and-plastic housing for indoor and outdoor installations. Its IP67 housing and fixed-lens design make it an option for entrances, corridors and other fixed monitoring positions.

The standard lens is 3.6mm, with 2.8mm and 6mm options available. The camera supports H.264/H.265 encoding, infrared illumination, a microphone, human and vehicle detection, and ONVIF connectivity.

This JBE-02V housing-series configuration has a 2.5-inch housing size specification and 12 IR LEDs. The housing series and IR LED count distinguish it from the other 5MP dome configuration; shared specifications do not establish any additional performance difference.

  • 5MP up to 20fps
  • PoE power
  • IP67 metal-and-plastic housing
  • 3.6mm fixed lens; 2.8mm / 6mm options
  • Microphone; human and vehicle detection
  • Samples: Paid samples; lead time 7 days.
  • Standard orders: MOQ 100 units.
  • OEM orders: MOQ 200 units for logo and label customization.
  • Bulk orders: Lead time 21 days.
  • Recorder and Ethernet cables sold separately.
Ask About OEM Customization

Technical data

Technical specifications

Other resolutions are available in the same housing series. This page describes only the JBE-502V 5MP configuration.

Camera and video

ModelJBE-502V
Camera typeVandal-resistant dome network camera
Resolution5MP
Image sensor1/2.8 inch CMOS
Frame rate5MP up to 20fps
EncodingH.264 / H.265
LensStandard 3.6mm fixed focal length; optional 2.8mm / 6mm
Infrared12 IR LEDs
AudioMicrophone supported
DetectionHuman and vehicle detection

Housing and connectivity

HousingMetal + plastic
Housing size specification2.5 inch
Ingress protectionIP67
EnvironmentIndoor / outdoor
PowerPoE
ConnectivitySupports ONVIF connectivity. Confirm compatibility with the intended recorder or VMS and the required functions before deployment.

Package and system

Included accessoriesScrew pack, mounting base and waterproof connector
Recorder and Ethernet cablesSold separately

PoE Camera Installation and Connections

All ports show functional connections only, not the rear-panel positions of any specific model. Check the selected camera, recorder, switch and power specifications before installation.

1. Direct Connection to a PoE NVR

  1. Connect each compatible PoE camera to a camera PoE port on the PoE NVR using an Ethernet cable.
  2. Connect the NVR LAN port to the router or local network. Connect a local monitor to the NVR HDMI output.
  3. Connect the specified NVR power supply. Check the PoE standard, per-port power and total power budget for the selected cameras.
  4. Configure and verify local recording. Internet access and the supported remote-access setup are required for viewing from outside the local network.

2. Connection via a PoE Switch

  1. Connect compatible PoE cameras to the PoE switch. A non-PoE IP camera needs its own specified power supply and an Ethernet data connection to the LAN.
  2. Connect the switch uplink to the router or LAN and connect the NVR LAN port to that same network. Follow the selected equipment documentation for the network topology.
  3. Power the NVR and PoE switch separately using their specified supplies. Connect the NVR HDMI output to a local monitor.
  4. Add compatible cameras to the NVR and verify recording. Confirm addressing, supported protocols, recording channels and the PoE power budget before installation.

Local recording and viewing on the connected monitor do not require internet. Remote viewing requires internet access and a supported, correctly configured remote-access method.

Direct Connection to a PoE NVR

Functional diagram: PoE cameras connect to NVR PoE ports; NVR LAN connects to a router, HDMI to a local monitor, and a separate supply powers the NVR.

Functional connections only; port positions are illustrative.

Ethernet Waterproof Connector Assembly

Follow these steps to assemble the waterproof cover around the camera’s Ethernet connection.

  1. Prepare the cable

    Slide the locking cap, rubber cable seal and waterproof housing onto the Ethernet cable before terminating the RJ45 plug.

  2. Connect and seal

    Terminate the RJ45 plug, make sure the O-ring is correctly seated on the camera connector, and insert the plug into the camera’s network socket.

  3. Secure the assembly

    Attach the waterproof housing to the camera connector, position the rubber cable seal and tighten the locking cap securely.

Assembly details may vary by connector kit. Follow the instructions supplied with your camera.

Ethernet Waterproof Connector Assembly

100%
Exploded view and assembly steps for a security camera RJ45 waterproof connector.

Private label sourcing

Need OEM / ODM customization?

Logo and label customization is available for OEM orders with an MOQ of 200 units.

Bulk and project inquiry

Request a product quotation

Tell us about your market, project and required configuration. No retail pricing or shopping cart is used.

  • Bulk procurement
  • Sample testing
  • OEM/private label
JBE-502VGet Quote
JBE-502V 5MP PoE Vandal-Resistant Dome Camera | JBCVISION